液体推进剂在轨剩余量测量方法研究进展

介绍了在轨航天器液体推进剂剩余量测量技术国内外研究进展,并展望了未来的研究方向。首先简要介绍了造成微重力条件下液体推进剂剩余量测量困难的原因;接着回顾了液体推进剂剩余量测量技术的发展脉络,将其技术发展分为技术萌芽、技术成熟和新技术探索三个阶段;然后从基本原理、误差分析、研究进展等方面综述了常用的簿记法(Book-Keeping,BK)、压力体积温度法(Pressure-Volume-Temperature,PVT)和热量激励法(Thermal Gauging Method,TGM)等液体推进剂在轨剩余量测量技术,对比分析了各种方法的优缺点;最后,展望了液体推进剂在轨剩余量测量技术的发展方向:一是利用不同测量技术在不同卫星寿命期间具有不同测量精度的特点,将多种测量技术进行结合,以提高整体测量精度;二是开发适用于卫星全寿命周期高精度测量的新方法。     

高能(450 kV)X射线参考辐射场附加过滤研究

利用MCNP程序对450kV X光机建立模型，计算各参考辐射质下的原级谱、平均光子能量。对ISO 4037-1中已有范围的管电压与附加过滤片厚度关系曲线进行二次拟合，确定模拟厚度范围。利用MCNP计算各附加过滤组合下的平均光子能量值，并与外推法得出的平均光子能量值进行对比，将相对偏差最小时的附加过滤作为最终确定值。从部分能量点的模拟与测量结果的对比可看出，模拟得出的平均光子能量在2%以内与PTB及中国计量院测量结果保持一致，附加过滤最大相对偏差为18%。     

基于类脑模型与深度神经网络的目标检测与跟踪技术研究

目标检测与跟踪技术广泛应用于交通、医疗、安保和航天等领域.目前，目标检测与跟踪技术面临目标微弱、背景复杂、目标被遮挡等挑战.同时，随着脑科学研究的不断深入，人们对人脑视觉系统的理解逐渐透彻，利用类脑计算解决复杂背景下高精度目标检测与跟踪问题成为相关领域的重要研究方向.本文结合神经工程导向的类脑模型和计算机工程导向的深度神经网络(Deep Neural Networks, DNNs)，提出多种基于类脑模型与深度神经网络的目标检测与跟踪算法，包括：基于演算侧抑制的目标检测算法，基于结构 对比度(Structure Contrast, SC)视觉注意模型的弱小目标检测算法和基于记忆机制与分层卷积特征的目标跟踪算法.实验结果表明，将类脑模型和深度神经网络应用于目标检测和跟踪领域，有利于实现复杂条件下的高精度目标检测和鲁棒性目标跟踪.     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

Variational Mode Decomposition for Rotating Machinery Condition Monitoring Using Vibration Signals

The failure of rotating machinery applications has major time and cost effects on the industry.Condition monitoring helps to ensure safe operation and also avoids losses.The signal processing method is essential for ensuring both the efficiency and accuracy of the monitoring process.Variational mode decomposition(VMD)is a signal processing method which decomposes a non-stationary signal into sets of variational mode functions(VMFs)adaptively and non-recursively.The VMD method offers improved performance for the condition monitoring of rotating machinery applications.However,determining an accurate number of modes for the VMD method is still considered an open research problem.Therefore,a selection method for determining the number of modes for VMD is proposed by taking advantage of the similarities in concept between the original signal and VMF.Simulated signal and online gearbox vibration signals have been used to validate the performance of the proposed method.The statistical parameters of the signals are extracted from the original signals,VMFs and intrinsic mode functions(IMFs)and have been fed into machine learning algorithms to validate the performance of the VMD method.The results show that the features extracted from VMD are both superior and accurate for the monitoring of rotating machinery.Hence the proposed method offers a new approach for the condition monitoring of rotating machinery applications.     

热障涂层在涡轮叶片应用中的热防护有效性

建立了含热障涂层的涡轮叶片简化传热模型,通过理论推导建立了热障涂层的有效性判据,并基于此进行了热防护有效性分析。理论分析与数值实验表明:由热障涂层带来的复合传热表面传热系数的变化会显著影响热障涂层的热防护效果；在发动机典型工况下,对于处于高温区的高压涡轮叶片前缘处,热障涂层引起的复合传热表面传热系数变化率最大值的范围为1.25%~10.83%以满足热防护有效性要求。在工程中应特别注意由于热障涂层的应用带来的复合传热表面传热系数的变化,否则会导致热防护失效,甚至产生反效果。      

半球谐振陀螺全角模式控制技术研究

介绍了半球谐振陀螺全角模式的工作机理及其技术特点。对全角模式下振型的控制进行了理论分析,采用乘法相干解调对陀螺振型参数进行提取,并采用参数激励方法对谐振子进行驱动和控制。设计了数字电路进行实验,结果表明该全角模式控制技术实现了半球谐振陀螺的角速率积分功能,能够0°～360°全角度敏感输出,测得的角速度测量值超过300(°)/s,角度测量线性度优于10~(-4),与传统的力平衡模式相比,半球谐振陀螺的动态特性得到大幅提升。     

通信拓扑切换下的多飞行器协同拦截方法

针对通信拓扑切换条件下的多飞行器协同拦截问题，提出了一种基于扩张状态观测器的协同制导方法。建立协同制导设计模型，将协同拦截问题转换为视线稳定条件下的剩余飞行时间调节问题。为解决机动目标状态不确定的问题，将目标的状态视作扰动，设计扩张状态观测器来估计机动目标的状态，并在制导律中对目标的机动进行补偿。利用有限时间一致性理论进行一致性控制协议的设计，实现各飞行器剩余飞行时间的有限时间一致，并利用Lyapunov稳定性理论分析通信拓扑切换情况下闭环系统的有限时间稳定性，给出了系统一致收敛时间。仿真结果表明，在通信拓扑变换的情况下，设计的观测器能够有效估计目标状态，且协同制导律能够满足对剩余飞行时间的控制要求，进而实现协同拦截。